Synthetic Seismogram

Ways to Tie Well-Log and Seismic Data
There are three ways to tie well-log and seismic data.
·        Stacking Velocities derived from seismic data
These provide the poorest time-depth control. There are several reasons for this, such as the processors’ need to avoid multiples and the limited offsets of real seismic data. Stacking velocities are essential in frontier plays where other data do not exist.
·        Velocity Surveys and Vertical Seismic Profiles (VSP)
VSP give the best velocity control. They use a surface source and geophones downhole (Figure 1). The checkshot uses “first breaks” (first reception of energy downhole after the shot), while the VSP analyzes the full sonic waveform over more closely-spaced geophone positions. If the first breaks are detectable, compression wave (P-wave) time vs. depth is determined as accurately as possible.
Figure 1. Configuration of a Velocity Survey or VSP.

·        Synthetic Seismograms derived from well data
These are a widely useful way to tie seismic time to log depth (Figure 2). Visual matching of seismic and the synthetic can reliably identify the sought-after reflector. Also, the synthetic shows how the detailed waveform and amplitude of the reflectors near the target are generated from the lithology. The interpreter can modify the logs to see what a hydrocarbon reservoir would look like if present. All that is needed is a sonic and density log from a well of interest.
Figure 2. Synthetic Seismograms.
On the minus side, synthetics do not give an absolute time-depth equivalence; and the synthetic may be a poor match for the real data. Synthetics may be used with a velocity survey to give best possible time-depth values together with information on reflection character.
Basics of the Synthetic Seismogram
A synthetic seismogram is created to simulate seismic data acquisition in your computer. The unknown physical properties of the earth beneath a seismic survey are known properties at a wellbore – P-wave acoustic velocity and bulk density. In acquiring seismic data, at the simplest, a seismic compressional wave (P-wave) is generated with a surface source; the wave travels at the acoustic velocity of the rock, which varies with lithology; the wave bounces off surfaces across which the impedance – the product of velocity and density – varies.
The strength of the reflection is measured with a reflection coefficient, which is the difference in impedance over the sum of the impedances. The wave then returns to the surface, where geophones detect the P-waves returning vertically. The time from generation of energy to its recovery at a geophone is the travel time; it depends on the velocities of the units traversed. The amplitude of the recovered energy is governed by the contrasts in velocity and density across the interfaces.
All the various geophone groups are recorded; data are processed, and an output section is generated. The interpreter then tries to identify target reflectors in time, analyze the seismic response to geology and fluids, convert time to depth, and drill.
In other words, a source wave is sent through a velocity field and a series of reflectors which yield seismic data, or:
            (Source Wave)*(Velocity Field)**(Reflection Series) = Data
Geology and hydrocarbons control both velocities and reflections. The objective is to resolve the reflection series using the data, knowing the source wave and estimating the velocity field:            (Reflection Series)=Data*((Source Wave)*(Velocity Field)**) -1
This is an “Inverse Problem.” There are direct and useful ways to do this (called “seismic inversion”), if the phase of the data is known, and the very low-frequency components of velocity and density that are not captured in seismic data can be added back.
One of the simplest ways to work the inverse problem is to take sonic velocity and density data from wells, run the seismic experiment with the sonic-derived velocity field and the sonic- and density-derived reflection series, assume a source wave similar to the seismic data, and compare the result to the data.
The well data can be varied to match what might exist away from the wellbore--but within the seismic survey. This can be done before the survey is acquired to answer a question such as: “Is a likely target visible?”
Preparation of Synthetics
A simple synthetic can be made on the back of an envelope, if there are only two or three reflections and great accuracy is not desired. Useful models can be prepared in this way (for example, Ewing and Caran 1982; Figure 3). However, for quantitative work on well logs and for synthetics to match real data, software is needed.
Figure 3. A 2-D envelope model of a volcanic tuff mound; from Ewing and Caran (1982).
Several good programs exist for synthetic generation – either stand-alone or as a part of a seismic interpretation package. Input log data come from digital files (LAS or LIS), from digitized logs, or from files produced by someone else’s digitization.
Output can be to an inexpensive printer or to a SEG-Y file that feeds directly into a workstation. One may even hire-out the process--with a paper log sent out and a synthetic received in return; however, this process is not interactive and will not result in utilization of the data to the fullest. The following is a suggested procedure for generating synthetics and tying them to real seismic data (also see Figure 4):
    1. Input sonic and density logs, along with other log curves as needed for correlation.
    2. In the synthetic generation program, run a Frequency Scan, which calculates traces with a range of frequency filters. The first trace should include high frequencies, to show the best possible time resolution of events. The other traces cut off at lower frequencies and bracket the actual frequency of the data at the target depth.
Compare to real data and select the best frequency filter. If the real data have automatic gain control (AGC), an AGC window can be applied.
    3. Run a Phase Scan. This set of traces should include zero, 90o, 180o (reversed polarity), 270o and minimum phase. Compare to real data and select the best phase.
Most airgun or dynamite data are minimum phase; most vibrator data is either zero or 90o phase.
    4. Tie data and synthetic and identify reflectors. Since log curves do not start at the surface, a few hundred milliseconds of mistie can be expected.
Calculate the time delay vs. the depth to the top of the synthetic for a given correlation and determine if the resulting velocity seems reasonable--or compare to a nearby velocity survey.
As the program allows, enter time-depth pairs from a survey and stretch or squeeze the synthetic to fit (this should give a fairly close match to the real data); pay attention to the datums of the synthetic and the seismic.
Problems
The most common problem is that the synthetic will not tie. Variants include:
·        Reflectors seem to come in at the wrong times.
It cannot be determined which reflector corresponds to the target. Velocity problems are the main suspect. Synthetics usually need to be stretched or squeezed to fit data, usually because of an inadequate measurement of the velocities in the wellbore. This occurs because:
    1. The hole is washed out; the sonic log fails to read true formation velocities. There may be cycle skips (which can be removed editorially). The log “noisiness” may be different for Long-Spaced Sonic vs. old-fashioned sonic logs.
    2. The formations are anisotropic. In real seismic, the energy does not travel purely vertically, but has a horizontal component which increases at far offsets. If the velocity of a formation depends on the direction of propagation, the rock is anisotropic, the far-offset seismic waves will not travel the same as those in a (vertical) borehole.
    3. There are dispersion effects. Sonic data in wells are acquired at kilohertz frequencies, while seismic waves are usually less than 120 Hz. If velocity varies with frequency, that is dispersion.
The best solution to the problem is to use checkshot information; this is the reason why acquiring it.
Vertical Seismic Profile (VSP) surveys are super-checkshots. VSPs also provide a direct look at the near-wellbore reflectors at the frequency band of real seismic. It is recommended that they be used if they are available.
·        The wiggles look different.
It is suggested that attempt be made to adjust the frequency and phase content of the wavelet used to create the synthetic. Minimum phase is recommended to match dynamite or airgun data, and zero or 90-degree phase for vibrators. One should observe the final bandpass filters on the header (or conduct a spectral analysis of the data on a workstation).
Synthetics should be compared to VSP data, if available. Synthetics are an interactive process.
·        There are extra reflections on the real data.
Real data may contain “multiple energy,” due to multiple bounces between reflectors within the earth or bounces off the surface interface. Multiples are usually very weak, because the stacking of modern, high-fold data discriminates against them. However, if the data are low-fold, the target is very deep, or the velocity profile varies significantly, multiples may be found in final sections.
Most synthetic programs allow for turning multiples on or off. Off is usually preferable, but it is simple to compare the two cases.
·        The wiggles are a lot stronger on the real data than on synthetics, especially at depth.
If the real data are generally strong at depth, the real data may have had an Automatic Gain Control (AGC) filter; the header should be checked. The synthetic seismogram can be run with the same AGC filter.
However, if only one or two reflectors are a lot stronger, this could be Amplitude vs. Offset (AVO) effect, due to anomalous amplitude in the far-offset seismic traces.
(Although the Amplitude vs. Offset technology should be reserved for a separate article, it should be noted here that these amplitudes are due to shear-wave generation at an interface by non-orthogonal traces. Because simple synthetic seismograms assume vertical incidence, “zero-offset”, AVO effects are not considered.)
Also, there is usually a considerable difference between the synthetic and the real data due to sampling area. The well-based data will sample a cylinder less than a meter in radius from the well. By contrast, a properly-migrated 3-D seismic trace may sample an area some 10 meters in radius, and the sampling zone in 2-D data could be hundreds of meters in width perpendicular to the line. Sonic and density properties may vary considerably.
VSP data provide major help in this case because it samples the earth at a scale closer to that of real seismic data.
Compromises: Fabricating Log Data
Proper synthetics use sonic and density data – but commonly only one of these, or perhaps only a resistivity curve, is available. The data from these wells may be used in some cases.
Statistical relations exist between velocity, density, and resistivity. These vary by area and by rock type. The two general forms are: the Gardner equation, relating density and velocity; and the Faust equation, relating resistivity and velocity. The effects of these techniques are shown in Figure 5.
Figure 5: Comparison of three synthetic seismograms for a deep Yegua well. The left-hand panels show the comparison of true sonic and density and the logs calculated using Faust, Gardner and Inverse Gardner (IG). All logs and synthetics are displayed in time and are corrected by velocity survey (the uncorrected IG-sonic was considerably too high). The deep, porous gas sandstone depresses density but not sonic, leading to errors using IG.

If sonic and no density data are available, synthetics can generally be prepared as usual. The time relationships between horizons will be accurate because time is based solely on velocity; but the reflector amplitude will not be completely accurate, for that is based on impedance (velocity times density).
If density is available, but no sonic, an inverse Gardner relationship should be used. Not all software has this built-in as part of its programs. (Many wells have a density/porosity curve, but not a bulk-density curve. The porosity curve can be used if the mud type is known; the log interpretation manuals should be used.)
If only resistivity is available, Faust’s equation should be used (Figure 5). Resistivity-generated sonic data usually need extensive stretching and squeezing to be valid. This requires a good velocity function, preferably a trusted velocity survey. In some areas resistivity will be a poor substitute, but it may be all that is available in some cases.
For best results, good log suites of wells in a project area should be used in preparing crossplots of velocity, density and resistivity in order to determine coefficients for the two relationships. (Neither relationship is very accurate for gas-bearing sandstone, nor are they useful for evaporites, unless they are identified specifically and are considered separately.)
AVO and 2-D Modeling
First, synthetics can also be generated that incorporate AVO effects. Determining these effects is very useful, even critical in many trends for identifying gas-bearing reservoirs or favorable lithologies. The AVO response of an interface is sensitive to the ratio of compressional-wave (P-wave) to shear-wave (S-wave) velocity. Therefore, in order to generate an AVO model, the S-wave velocities as well as P-wave velocities need to be known.
The shear velocities come from either a full-waveform sonic log in fast rocks, or a dipole sonic log in slow formations. If no shear information is available, lithology allows an estimate of Vp/Vs; however, this is not very good. If dipole or full-waveform sonic logs are run in any well, the AVO synthetic should be included as normal procedure.
Second, if a series of synthetics in which density and velocity are varied to simulate a geologic or fluid change, a 2-D model is being created. A set of varying synthetics stitched together along a traverse approximates a migrated seismic section, but no raypath-dependent effects are included. Such models are quick, and very useful for understanding the seismic response to geologic changes. There is software available for this exercise in many synthetic packages.
However, if dips or lateral velocity changes are substantial, or if amplitudes are important, a raytracing algorithm is needed. These raytracing modelers create a synthetic migrated section but include shadowing effects due to the bending of raypaths.

 

posted by Geology on 04:22

0 comments:

Post a Comment

Subscribe to: Post Comments (Atom)

Search